Tesla Model S: Wire Harnesses
RST-182-F
|
Tesla part number: |
1013716-00-A |
|
|
Description: |
TOOL, HARNESS, 4-WAY BREAKOUT |
|
Model: |
Roadster, Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-182-G
|
Tesla part number: |
1013750-02-A |
|
|
Description: |
TOOL, HRNSS, PKG PAWL BRAKE RELSE, 2.0 |
|
Model: |
Roadster, Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-182-H
|
Tesla part number: |
1013750-01-A |
|
|
Description: |
TOOL, HRNSS, PKG PAWL BRAKE RELSE, 1.5 |
|
Model: |
Roadster, Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-184-C
|
Tesla part number: |
1013758-01-A |
|
|
Description: |
MODEL S TPMS TOOLING CABLE |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-189
|
Tesla part number: |
6005463 |
|
|
Description: |
ASY,CABLE,ESS LOGIC HARNESS,DARKSTAR MRK |
|
Model: |
Roadster |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-190
|
Tesla part number: |
6005461 |
|
|
Description: |
ASY,CABLE,BMB CAN/POWER |
|
Model: |
Roadster |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-306
|
Tesla part number: |
1013230-00-A |
|
|
Description: |
Cable, HSD to Ethernet, Model S (CAT5 to HSD Diagnostic) |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-307
|
Tesla part number: |
1014593-00-A |
|
|
Description: |
HARNESS,LOGIC,HVBAT,SERVICE,MODEL S |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-348
|
Tesla part number: |
1021185-00-A |
|
|
Description: |
Float Charger Jumper Cables |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
RST-376
|
Tesla part number: |
1030924-00-A |
|
|
Description: |
EPB Release Tool, Harness |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
n/a |
|
Small Hand Tools
1058193-00-A
|
Tesla part number: |
1058193-00-A |
|
|
Description: |
Bussman FP-2 Fuse Puller |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
Forward Junction Box - 2nd Generation - 40 Amp Fuse (RWD) (Remove
and Replace) |
|
1058194-00-A
|
Tesla part number: |
1058194-00-A |
|
|
Description: |
Duo Tongs Universal Fuse Puller |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
Forward Junction Box - 2nd Generation - 20 Amp Fuse (RWD) (Remove
and Replace) |
|
1058696-00-A
|
Tesla part number: |
1058696-00-A |
|
|
Description: |
Wiper Arm Removal Tool |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
Special Tools - Wiper Arm Removal Tool |
|
1062500-00-A
|
Tesla part number: |
1062500-00-A |
|
|
Description: |
Magnetic Field Viewing Card |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
Hub - Front - LH (Remove and Replace) Hub - Rear - LH (Remove
and Replace) |
|
1064740-00-A
|
Tesla part number: |
1064740-00-A |
|
|
Description: |
Adhesive Scraper |
|
Model: |
Model S |
|
Status: |
Distribution |
|
Special project/SOP: |
SOP |
|
Instructions: |
Windshield Assembly (Remove and Replace) Liftgate Glass (Remove
and Install)
Liftgate Glass (Remove and Replace) |
|
READ NEXT:
Raising and supporting the vehicle
Jacking points on the Model S
Caution: Do not jack or support the vehicle on any other points
than those shown. Failure to comply will result in dama
Fluids
Air conditioning
Depending on its intended sales region, the air conditioning system is
filled with R134a or 1234yf refrigerant. Refer to the label on the RH
frunk trim.
If oil nee
The HV battery alignment rods assist in aligning the HV battery during
installation.
Note: This tool is intended to be used by 2 technicians.
To use the alignment rods:
Position the tabl
SEE MORE:
The HVAC and battery coolant circuits are sealed to prevent the
discharge of refrigerant. The refrigerant must be recovered before any
removal of system components using the recommended equipment.Two
ports are provided on the HVAC system and are accessible under the hood.
Warning: Ens
Installation
Use a scraping tool to remove the majority of
the adhesive from the body, leaving a smooth layer of the original
adhesive approximately 1 mm thick or less.
Remove all existing butyl patches and replace
them with new ones
Lifting and Jacking
